Ukulele Making | CoolUkulele.com

I stumbled across these old plans for making a ukulele from a cigar box. Someone may want to actually try this out. If not, it's still very interesting to read. Check it out (I chopped it up into smaller paragraphs to make it easier to read): How To Make a Cigar Box Ukulele The one-string banjo, the cigar box guitar, and similar vaudeville favorites are giving way to the tantalizing ukulele, and the home mechanic, to be up to date in his musicla craftsmanship, must fall in line. The size of this instrument makes it especially suited to the cigar-box type for body construction, as detailed in the several sketches and shown in the photograph reproduced. This neat ukulele was made at a cost of 30 cents by careful selection of materials from the shop scrap stock. This Cigar-Box Ukulele cost the maker 30 cents, and Affords him the Pleasures of a More Expensive one A cigar box of good quality Spanish cedar, about 2-1/2 x 6 x 6 in., as shown in Figure 1 is used for the body. Figure 1 Remove the paper carefully, so as not to mar the surface, soaking it if necessary. Take it apart, and if the nail holes are too numerous, or broken out, trim off the edges. Fit the parts of the body together, as shown in Figure 2, the top and bottom pieces resting against the side and end pieces, and the latter between the sides. Cut the 2-1/2 in. hole in the top piece as shown, 3-3/4 in. from the neck end. To reinforce the body make strips A, 1/4 in. square, and fit them to be glued into the corners at the top and bottom. Make strips B, 1/4 by 5/8 by 4-1/2 in., and glue them under the top and on the bottom as indicated in Figure 2. Figure 2 The final assembling and gluing of these parts, using animal glue, should be done after the bridge C is in place, and the other parts are made. The bridge is of hard wood hollowed underneath the notched edge, as detailed, and is fitted with a metal string contact. Spanish cedar or mahogany is suitable for the neck, detailed in Figure 3. A single piece is best, but the extension for the pegs and the wider end at the body may be joined and glued to the main portion of the neck. Dowels should then be used to reinforce the joints. The outline of the parts of the neck are shown in detail in Figure 3. In the sectional view at the right, the shape of the neck at the thinnest and thickest parts is shown by the two upper curved, dotted lines. The nut D is made of mahogony, walnut, or other hard wood, the grain extending lengthwise, and the notches for the strings spaced as shown. Figure 3 The making and spacing of the frets must be done very carefully. They are of aluminum, brass and other metals being suitable also. Make the frets 1/16 by 3/16 in. and cut grooves 1/8 in. deep for them. The spacing of the frets is determined as follows, a standard practice: The distance from the metal string-contact on the bridge to the nut should be measured carefully. The first fret, near the head, is 1/18 of this distance from the nut, the total length being in this instance 13 in. The second fret is set 1/18 the distance from the first fret to the bridge; the third, 1/18 from the second fret to the bridge, etc. The frets must fit tightly in the grooves, requiring no special fastening. The tuning pegs may be bought or made. In assembling the parts, fasten the end of the body to the neck, with glue, reinforced by screws. Set its upper edge parallel with the fingerboard, and so that the latter is flush with the top of the body, when fitted to it. Assemble the body, without the top, gluing it to the end, fixed to the neck. When this portion is thoroughly dried, fit the top into place finally, and glue it. The whole construction is then cleaned, sandpapered, stained, and shellacked or varnished. The stringing of the instrument is simple, and the strings may be purchased in sets. Enjoy!